Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateGenie Torsion Spring Replacement: The Summerlin Owner’s Guide
We replace Genie torsion springs in Summerlin, and the installed price typically lands between $180 and $340 depending on the spring configuration. A failed torsion spring usually shows itself as a door that won’t lift, a loud bang from the garage, or a gap in the coil you can see with the door closed. Most Summerlin homeowners find it the same way: they hit the opener, hear the motor hum, and the door doesn’t move.
The torsion spring is the part that counterbalances the door’s weight. It’s under tension every hour of the day, and Nevada’s dry air and heat cycling work on it year-round. When a Genie spring on a Summerlin door finally goes, it usually goes all at once.
Which Genie Models This Applies To
Genie torsion springs are matched to the door, not to the model number on the opener box. The Genie name on your wall unit tells us which opener you have, but the torsion spring on the shaft above the door was sized when the door was hung, and that sizing depends on door weight and track height. The two pieces of information live on different hardware.
Here’s what we check when we arrive. The torsion tube diameter and spring length on the shaft, the wire diameter measured in thousandths of an inch, and the door-weight rating stamped on the door’s label. A Genie spring at 0.25-inch wire diameter and a 27-inch length is a different part from a 0.25-inch at 32 inches, and putting the wrong length back on a door does real damage over time. The compatibility issue most homeowners miss: a previous owner or a prior installer may have swapped in a spring sized for a different door, which is why the door can feel wrong even after a spring replacement.
On the OEM-versus-aftermarket question, we source Genie-compatible torsion springs sized to your door and matched in wire diameter, and we’ll show you the brand and spring specs before installation. An aftermarket spring of the correct spec performs identically to OEM; a wrong-spec OEM spring does not. Fit matters more than the label. We service Genie alongside LiftMaster and Chamberlain, so if your house has mixed brands between door and opener, that doesn’t slow us down.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your Genie Torsion Spring Replacement Is Failing

- A loud bang from the garage. The spring has snapped. You’ll often find the door still closed and the opener stalling. Stop using the opener at this point; running the motor against a broken spring wears the gear and can pull the door off its tracks.
- A visible gap in the coil. With the door closed, look at the spring above the door on the center shaft. A clean break shows as a gap 1/8-inch to 1-inch wide. Missing winding on one side means one of two springs has failed; they should always be replaced as a pair.
- The door rises a few inches and stops. If the opener runs but the door barely lifts, the spring has lost tension, so the motor is trying to lift the door’s full weight unaided. Continued use burns out the opener.
- The door feels heavy when lifted by hand. With the opener disengaged, a door in working order lifts with light effort and stays up on its own. A door that feels like dead weight needs a spring, not a tune-up.
- Uneven lift or a tilted door. One spring has lost tension first. The door rises crooked, one side trailing, and the opener strains. This is the stage where a repair is still cheap.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Genie torsion spring replacement in Summerlin runs $180 to $340 installed for a standard single-door configuration. Most jobs land near the middle; you’re at the top of the range when the door has two springs and both are being replaced, or when a snapped spring has taken out a cable or cable drum along with it, which we’ll see in the photo record before we quote.
What’s included at that price: the torsion springs, the labor to wind and install, the safety check on cables and drums, a balance test, and a documented photo record of what we found and what we replaced before we leave. That photo record is part of how we work (Clause 4 of The Haven Standard), not an add-on. We replace paired springs as a set even if only one has broken, because a new spring beside an old one is a door waiting to go crooked in six months.
We quote a flat, written price and written scope before any work begins. The number doesn’t change when the technician opens the cardboard. Parts and labor are broken out on the quote so you can see what the spring cost and what installing it cost.
DIY or Call Us?

You can safely observe. Look at the spring, photograph the gap, measure the visible length, and note whether the door has one spring or two. Reading your garage door’s label to confirm weight rating is useful information. All of that helps us size the part before we come out.
The winding is a different category of job. Torsion springs are under hundreds of pounds of tension. A winding bar slipping out of the cone is the injury most commonly associated with garage door work, and it happens to people who’ve watched the videos. We don’t give step-by-step instructions for it, and we’d rather you didn’t try. Cables and drums are the same story.
If you’ve already had the door evaluated and the spring is failing, call us at (844) 797-3654. We can often come out same day for a spring replacement, and the quote is free.
FAQs
The typical Genie torsion spring is rated for 10,000 cycles, where one cycle is a full open-and-close. For a Summerlin home that opens twice a day, that’s roughly 13 years, but Nevada’s heat reduces that. Dry air, dust, and temperature swings between 40°F mornings and 110°F afternoons wear the wire faster than in cooler climates. In Summerlin we see springs fail as early as seven years on south-facing doors. If yours is older than that and you’ve noticed the signs above, call us at (844) 797-3654 for a no-charge assessment.
No. A torsion spring is a single continuous coil of wire, and a break cannot be welded or spliced to a safe standard. Coil overlength or “spring repair” kits exist in the market and we don’t install them, because a spliced spring can’t be trusted under load. Replacement is the only repair that holds. It costs $180 to $340 in Summerlin, and the money buys real safety margin.
Most single-door Genie spring replacements take 60 to 90 minutes once we’re on site, and we’ll quote the time window when we confirm the appointment. If the door has two springs, add 20 to 30 minutes. If cables or drums also need work, we’ll say so up front, not after the door’s already on the floor. Call (844) 797-3654 for a free estimate and we’ll have the window in writing.
We size the spring to your door’s rating, wire diameter, and shaft length, and we source Genie-compatible springs from suppliers that publish full coil specifications, not a generic “fits most doors” spring. We’ll show you the label and the spec matching our measurement. You don’t commit to a part you can’t see verified. Call (844) 797-3654 and we’ll walk through the sizing before the visit.
If you’re unsure which spring or whether the door has one or two, call us at (844) 797-3654 for a free estimate. We can often come same day, we’ll photograph what failed before we quote, and the price is written before we start. Servo Garage Doors Summerlin is an independent service provider and is not affiliated with Genie.
Written by the team at Servo Garage Doors Summerlin, serving Summerlin and nearby areas.