Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateCraftsman Torsion Spring Replacement: The Summerlin Owner’s Guide
We replace Craftsman-compatible torsion springs in Summerlin for $180 to $340 installed, and most spring replacements are handled same day. The torsion spring is the horizontal coil mounted above your door on a steel shaft; it carries the door’s weight, and when it breaks you’ll hear a loud snap from the garage. Then the door won’t lift, or it lifts a few inches and stops because the opener can’t carry the load alone. Most Summerlin owners find out at 7 a.m. on a workday, standing in the driveway pulling the release cord and getting nothing.
This page covers the part that failed, how to match it to your Craftsman model, and what the replacement costs before anyone touches the door. The price is quoted and agreed before work starts, per Clause 1 of The Haven Standard, and the technician photographs the failed spring before quoting anything, per Clause 4.
Which Craftsman Models This Applies To
Craftsman torsion springs wear across the whole line: the 5000 and 5300 series, the 1000 and 2000 series openers, and the chain-drive and belt-drive units that were sold at Sears and later at Lowe’s. The opener model tells you less than the door tells you. What determines the correct spring is the door itself: its weight, height, and whether it has one spring or two. A Craftsman opener is just the motor; it doesn’t dictate the spring size.
Springs are matched to wire diameter, inside diameter, and length. A common spec on a two-car Summerlin door is a 0.243-inch wire, 2-inch inside diameter, 33-inch length pair, but that number varies with door weight and brand, so we measure rather than assume. Your door’s spring color codes indicate wire gauge, though the paint often fades faster in Nevada heat. That’s a compatibility gotcha: a faded spring can read as a different gauge and steer an owner toward the wrong replacement.
Craftsman never manufactured its own torsion springs; the door came from a door maker and the opener from the Craftsman line. That means a quality aftermarket spring matched to your door’s exact measurements performs the same as a factory part, and often better when the original used a lower-cycle spring. We source springs rated for 15,000 to 25,000 cycles, and we write the spec onto your invoice so you know what’s going in the door.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your Craftsman Torsion Spring Replacement Is Failing

You usually don’t see the break; you hear it and then feel it. Here’s what points to a failed or failing torsion spring:
- A loud snap from the garage, then nothing. That’s the spring letting go under tension. The door won’t lift because the spring no longer counterbalances it.
- The door rises a few inches and stops. The opener is straining to lift a door that suddenly weighs far more than the motor is rated for. Stop using it; a dying opener can burn out or the door can drop.
- A visible gap in the coil. Look at the spring above the door without touching it. A clean break mid-coil is the classic failure, and it’s more common in Summerlin’s dry heat because cycling and temperature swings weaken the metal faster.
- Uneven or crooked door lift. If you have two springs and one has broken, the door lifts lopsided because the remaining spring is doing all the work.
- Loud grinding or jerking during opening. A spring that’s losing tension forces the opener and rollers to absorb the load, which shows up as noise and wear on unrelated parts.
If any of those describe your garage, don’t keep running the opener. Each cycle on a broken spring loads the motor and cables in ways they weren’t designed for, and that turns a $180 to $340 spring replacement into a bigger repair.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Craftsman torsion spring replacement in Summerlin runs $180 to $340 installed. That’s the whole job: parts and labor, quoted flat before the technician starts. What moves the number is the number of springs, the wire gauge (heavier doors use heavier springs), and whether the door uses one or two. A two-spring door commonly lands toward the top of the range.
Here’s how the pricing breaks down:
- Single-spring replacement: lower end of the $180 to $340 range.
- Two-spring replacement: upper end of that range.
- What’s included: the spring(s) matched to your door’s spec, removal of the broken spring, installation, tension calibration, and a function test.
- Warranty on the work: covered by the 365-Day Done Right Promise. If it isn’t right, we make it right.
The written price and written scope come before any work, so the invoice doesn’t surprise you later. That’s Clause 1, not a sales line. If you’ve got a lower written estimate from another company, bring the paperwork and we’ll give you a free second opinion on it.
DIY or Call Us?

A torsion spring is one of the few garage door parts we’ll tell you plainly not to replace yourself. The spring stores enough energy to cause serious injury if it releases while you’re working on it; winding and unwinding it requires the right tool and the right turns, and amateur attempts send people to the emergency room. We’re not being dramatic about it. It’s a genuinely dangerous component, and the honest advice is to leave it to a trained technician.
What you can do safely: look at the coil from the floor for an obvious gap, check whether the door lifts evenly, and stop running the opener once you suspect a break. That’s your check. The rest is the swap.
Our technicians have up to 11 years of experience, are background-checked and work under The Haven Standard, and you get the documented photo record of the failed spring and the finished job when they leave. Call (844) 797-3654 and we’ll get a technician out with a written price first. Spring replacement is same-day work, and emergency calls are answered by a live person, day or night.
FAQs
A standard torsion spring lasts 10,000 to 15,000 cycles, and a premium one lasts up to 25,000. In Summerlin, where dry heat and big temperature swings wear metal faster, it’s realistic to expect the lower end of that range. We fit higher-cycle springs to stretch the lifespan so you’re not back here in a few years. Call (844) 797-3654 for an exact quote on a higher-cycle spring for your door.
A broken torsion spring can’t be repaired; it has to be replaced. Once the coil snaps, the metal’s lost its tension and there’s no safe way to weld or patch it. The good news is that replacement is straightforward and costs $180 to $340 installed, which is one of the cheaper repairs on a garage door. Call for a free estimate on your specific door.
A single-spring replacement usually takes about an hour, and a two-spring job runs a bit longer. The technician measures, sets the written price, and does the swap in one visit, then calibrates the tension and tests the door before leaving. Same-day scheduling is common for spring calls. Call (844) 797-3654 and we’ll get a time on the calendar.
We match the spring to your door’s exact measurements: wire diameter, inside diameter, and length, plus the number of springs on your shaft. Since Craftsman didn’t make its own springs and the door maker varies, we measure rather than trusting a sticker, and we source a spring rated for the cycle count you’re paying for. The spec goes on your invoice so you can see exactly what went in. We service all the major brands, and this is the same process we use for LiftMaster, Chamberlain, and Genie doors. Call for a free estimate and we’ll walk you through it.
Servo Garage Doors Summerlin is an independent service provider and is not affiliated with Craftsman.
When you’re ready, call (844) 797-3654 for a free estimate. We’ll photograph the failed spring, put the price in writing before any work starts, and get your door lifting again.
Written by the team at Servo Garage Doors Summerlin, serving Summerlin and nearby areas.